|
 |
Converting the Chrysler Poly motor to Hemi |
Development and Description
Less expensive, lighter variants of the Chrysler hemi motors were developed, and introduced in 1955 for installation in the Windsor and Saratoga, in place of the flathead six-cylinder motors previously used. These new motors used the existing hemi block, but completely different heads, intake and exhaust manifolds, pushrods, pistons, etc. with only a single rocker shaft in each head. These motors were called “poly” (for poly-spheric: meaning “more than one sphere”), since the combustion chamber was now formed by two separate concave domed shapes (the valve seats and surrounding reliefs).
Poly motors are also called single rocker shaft (“SRS”), while hemi motors are dual rocker shaft (“DRS”).
Conversion of Chrysler Poly Motors to Hemi
1955-58 Chrysler Saratoga and Windsor 301, 331 & 354 poly motors can be converted to hemi by substitution of hemi parts using Chrysler parts only.
If the original pistons are used, the motor will run, but have lower compression since the poly piston does not have a compression dome. The hemi heads must match the low deck height to insure manifold alignment; if 392 heads are used the manifold won't fit. The crankshaft balance will also be affected, since the hemi pistons are heavier in most cases due to the dome. Heads should be selected from motors of the same or smaller bore size to prevent the chamber from overhanging the bore, but some choices may be available as to port size, valve size and chamber volume. Hemi head bolts must be used.
DeSoto & Dodge Poly Motors
Please note that, although poly motors were used in DeSoto models, they are Dodge engines; there is no poly motor based on the DeSoto hemi series. The Dodge poly motors and 1955-56 Plymouths using these motors can be converted by using Dodge hemi parts.
Poly “A” Motors
There is no hemi motor based on the “A” series poly motor as used in Plymouths 1956-67 and some Dodges 1958-59, and no conversion by direct substitution is possible. The “A” poly motor is very similar in design to the earlier hemi-derived poly motors, but parts are not generally interchangable.
Notes
All 1951-57 Chrysler, DeSoto, Dodge and Plymouth V8 motors, regardless of family, size or type, have the distributor located in the rear of the engine. Only 1958-* “B” and “RB” type motors, both wedge and hemi, have front-mounted distributors.
There is no commonality of parts or dimensions between the early (1951-58) motors and late (1964-*) hemi motors, which were developed by adapting hemi technology to the “RB” motors.
The Table below contains “Maximum Compression Distance” data. This is not measured or taken from factory information, it is calculated on the basis of .000” deck height (with the piston's top surface flush with the cylinder bank head gasket surface) with the tallest possible theoretical piston (measured between the piston pin center and the top surface). |
Hemi & Poly Motor Data |
Motor |
Year |
Size |
Bore Size |
Deck Height |
Rod Length |
Stroke Length |
Maximum Com. Dist. |
Bore Centers |
Plymouth poly only; 1954-56 Dodge motors used in all applications |
1955 |
241” |
3.4375” |
9.29” |
5.9375” |
3.25” |
1.727” |
4.1875” |
259” | 3.5625” |
1956 | 270” |
3.625” |
Dodge, low deck hemi: 1953-55; poly 1955-56 259” poly only |
1953-54 |
241” |
3.4375” |
1955 |
259” |
3.5625” |
1955-56 |
270” |
3.625” |
Dodge, raised deck hemi: 1956-57; poly 1956-58 |
1956 |
315” |
3.625” |
10.38” |
6.618” |
3.80” |
1.862” |
1957-58 |
325” |
3.6875” |
Plymouth A poly only 318” 1958 Dodge also 326” 1959 Dodge only |
1956-57 |
277” |
3.75” |
9.60” |
6.123” |
3.125” |
1.914” |
4.46” |
1957 |
301” | 3.91” |
1956 |
303” | 3.8125” | 3.31” | 1.822” |
1957-66 |
318” | 3.91” |
1959 |
326” | 3.95” |
DeSoto, low deck; hemi only; Dodge motors used in 1955 poly applications |
1952-54 |
276” |
3.625” |
9.54” |
6.067” |
3.34375” |
1.801” |
4.3125” |
1955 |
291” |
3.72” |
DeSoto, raised deck; hemi only Dodge motors used in 1956-58 poly applications |
1956 |
330” |
3.72” |
10.37” |
6.625” |
3.80” |
1.845” |
1956-57 |
341” |
3.78” |
1957 |
345” |
3.80” |
Chrysler, low deck 301” poly only; 331” poly 1956 354” poly 1956-58 |
1955 |
301” |
3.625” |
10.32” |
6.625” |
3.625” |
1.882” |
4.5625” |
1951-55 |
331” |
3.8125” |
1956 |
354” |
3.9375” |
Chrysler, raised deck; hemi only |
1957-58 |
392” |
4.00” |
10.87” |
6.956” |
3.906” |
1.961” |
(Click here for the next page)
 |