These spares are for the Mikuni “VM” type (round slide,
aluminum-bodied, spigot mount, “GP”) carbs as shown, right, except as noted (* = radial
slide). The prices are current as of October 2005, but will change with time. Limited
quantities available these items; the prices shown are for parts in stock only.
You
must know what model you have, and which parts fit - parts are not
returnable. If the exact size you requested is not available, we will send
the next richer size unless you specify “only”, etc. Some brass parts (jets, needle jets, etc.) have been removed from carburetors and are therefore “used”, but are still in like-new condition as to their metering accuracy. If not acceptable, please specify “new only” when ordering. These carburetors and parts are NOT RETURNABLE. If the part you are looking for does not appear on this page, I can’t supply it.
For new Mikuni carburetors, click here to go to KNS Cycle: |
|
Slides (throttle valves) have either left or right side idle screws (as seen look- ing down the air horn), and 1 of 3 different guide pin groove widths: 2.05mm = .081”, 2.60mm = .102”, 3.05mm = .120”. Shown here in the diagram, right, is a right side idle model, with the slide’s guide pin groove on the left. The slides shown below are exactly as described. | |
Mikuni Parts |
Description |
Mikuni Part # |
Fits |
Sizes in Stock (may not have pairs of all sizes) |
Price |
Throttle Valve (Slide)
Brass slides are chrome plated
Aluminum slides are anodized |
VM28/80 |
28-30mm zinc flange, 28mm zinc clamp, left idle, 2.05mm groove, aluminum |
3.5 |
$ 10.00 |
VM32/22 |
30-34mm VM & 32-34mm zinc flange, left idle, 2.05mm groove, aluminum |
3.5 |
$ 10.00 |
VM28/156 |
30-34mm VM & 32-34mm zinc flange, left idle, 2.05mm groove, brass |
1.5, 3.5 |
$ 19.00 |
VM36/13 |
36mm, left idle, 2.05mm groove, brass |
1.5 |
$ 38.00 |
VM36/36 |
36mm, left idle, 3.05mm groove, brass |
2.5 |
$ 38.00 |
VM38/10 |
38mm, right idle, 2.05mm groove, brass |
3.0, 3.5 |
$ 34.50 |
VM38/24 |
38mm, right idle, 3.05mm groove, brass |
3.5 |
$ 34.50 |
VM40/23 |
40-44mm, left idle, 2.60mm groove, brass |
1.5, 2.0, 2.5, 3.0, 3.5 |
$ 25.00 |
VM40/02 |
40-44mm, left idle, 2.60mm groove (3.05mm is listed), aluminum |
1.5 |
$ 19.00 |
Needle Jet |
784-132* |
RS, HS* |
Type 568*: Y-6, Y-8, Z-0 |
$ 13.25 |
Main Jet |
N100.604 |
8mm large round slotted head |
105, 112.5, 115, 117.5, 120, 160, 165, 170, 175, 180 |
$ 3.00 |
Air Jet |
BS30/97 |
|
|
|
2.0 |
$ 1.00 |
Description |
Mikuni Part # |
Fits |
Bolt Centers |
ID |
Price |
Rubber Mounting Flange |
VM34-200-1 |
30-34mm |
60mm 2.36” |
36mm |
$ 11.15 |
This Rubber Mounting Flange (above) is NOT an adapter to your motor. It will NOT bolt on to your motor. I only have 1 left of these, please do not order 2. The “Bolt Centers” distance shown (above) is NOT the same as your intake manifold. I cannot supply adapters to your motor. |
Starter Plunger, Cable |
VM15SC4/85 |
all 30-44mm VM |
Part of cable-operated starter system |
$ 2.50 |
Starter Plunger Fitting, Cable |
VM15/37 |
all 30-44mm VM |
Part of cable-operated starter system |
$ 1.50 |
Needle Clip Spacer Set |
VM-SPC |
.020” shim, moves the needle up ½ clip position, for fine-tuning all 30-38mm VM carburetors, set of 4 |
$ 1.00 |
Want more performance
from your older Triumph, BSA, Norton, Royal Enfield or Matchless twin?
Already have Mikuni carburetors, but don’t know how to adjust them? Doesn’t run “right”, and won’t respond to the changes you’ve made? Can’t make any sense of the original Mikuni factory or Sudco “instructions”? This booklet will help you; click the cover for details. | | |
Want more performance from your Harley-Davidson Knucklehead, Panhead, 45, or U-Series? Already have a Mikuni carburetor, but don't know how to adjust it? Doesn't run "right", and won't respond to the changes you've made? Can't make any sense of the original Japanese "instructions"? Looking for an affordable alternative to replacing or rebuilding your tired Linkert? This booklet will help you; click the cover for a complete list of contents. | | |